OSPF6D.CONF(5)

NAME
ospf6d.conf - OSPF for IPv6 routing daemon configuration file

DESCRIPTION
The ospf6d(8) daemon implements the Open Shortest Path First protocol version 3 as described in RFC 5340.

The ospf6d.conf config file is divided into the following main sections:

Macros
    Definitions of variables that can be used later, simplifying the configuration file.

Global configuration
    Global settings for ospf6d(8). A number of global settings can be overruled in specific areas or interfaces.

Areas
    An OSPF router must be a member of at least one area. Areas are used to group interfaces, simplifying configuration.

Arguments not beginning with a letter, digit, or underscore must be quoted.

Additional configuration files can be included with the include keyword, for example:

    include "/etc/ospf6d.sub.conf"

  Macros
A macro is defined with a command of the form name=value. The macro name can contain letters, digits, and underscores and cannot be a reserved word (for example, area, interface, or hello-interval). Within unquoted arguments, the string $name is later expanded to value.

For example:

    hi="5"
    area 0.0.0.0 {
    	interface em0 {
    		hello-interval $hi
    	}
    }

The same can be accomplished by specifying the hello-interval globally or within the area declaration.

  Global configuration
All interface related settings can be configured globally, per area and per interface. The only settings that can be set globally and not overruled are listed below.

fib-priority prio
    Set the routing priority to prio. The default is 32.

    fib-update (yes|no) If set to no, do not update the Forwarding Information Base, a.k.a. the kernel routing table. The default is yes. Setting fib-update to no will implicitly set the stub router option to ensure that no traffic tries to transit via this router.

rdomain tableid
    Specifies the routing table ospfd(8) should modify. Table 0 is the default table.

    [no] redistribute (static|connected| default) [set ...] [depend on interface]
    [no] redistribute prefix [set ...] [depend on interface]
    [no] redistribute rtlabel label [set ...] [depend on interface] If set to connected, routes to directly attached networks will be announced over OSPF. If set to static, static routes will be announced over OSPF. If set to default, a default route pointing to this router will be announced over OSPF. It is possible to specify a network range with prefix; networks need to be part of that range to be redistributed. Additionally it is possible to redistribute based on route labels using the rtlabel keyword. By default no additional routes will be announced over OSPF.

    redistribute statements are evaluated in sequential order, from first to last. The first matching rule decides if a route should be redistributed or not. Matching rules starting with no will force the route to be not announced. The only exception is default, which will be set no matter what, and additionally no cannot be used together with it.

    With the depend on option, redistributed routes will have a metric of 65535 if the specified interface is down or in state backup. This is especially useful on a carp cluster to ensure all traffic goes to the carp master.

    It is possible to set the route metric and type for each redistribute rule. type is either 1 or 2. The default value for type is 1 and for metric is 100. Setting more than one option needs curly brackets:

        redistribute static set { metric 300 type 2 }

router-id address
    Set the router ID; if not specified, the lowest IPv4 address of the interfaces used by ospf6d(8) will be used. A router ID must be specified if no IPv4 address is configured on any interfaces used by ospf6d(8).

rtlabel label external-tag number
    Map route labels to external route tags and vice versa. The external route tag is a non-negative 32-bit number attached to AS-external OSPF LSAs.

spf-delay seconds
    Set SPF delay in seconds. The delay between receiving an update to the link state database and starting the shortest path first calculation. The default value is 1; valid range is 1-10 seconds.

spf-holdtime seconds
    Set the SPF holdtime in seconds. The minimum time between two consecutive shortest path first calculations. The default value is 5 seconds; the valid range is 1-5 seconds.

    stub router (yes|no) If set to yes, all interfaces with active neighbors will have a metric of infinity. This ensures that the other routers prefer routes around this router while still being able to reach directly connected IP prefixes. The stub router option is automatically enabled if either the sysctl(8) variable net.inet6.ip6.forwarding is set to a value different to 1 or if the FIB is not coupled.

  Areas
Areas are used for grouping interfaces. All interface-specific parameters can be configured per area, overruling the global settings. These interface-specific parameters need to be defined before the interfaces.

area address|id
    Specify an area section, grouping one or more interfaces.

        area 0.0.0.0 {
        	hello-interval 3
        	interface em0
        	interface em1 {
        		metric 10
        	}
        }

Area specific parameters are listed below.

demote group [count]
    Increase the carp(4) demotion counter by count on the given interface group, usually carp, when no neighbor in the area is in an active state. The demotion counter will be decreased when one neighbor in that area is in an active state. The default value for count is 1.

    For more information on interface groups, see the group keyword in ifconfig(8).

  Interfaces
Each interface can have several parameters configured individually, otherwise they are inherited. An interface is specified by its name.

    interface em0 {
    	...
    }

Interface-specific parameters are listed below.

demote group
    Increase the carp(4) demotion counter by 1 on the given interface group, usually carp, when the interface state is going down. The demotion counter will be decreased when the interface state is active again.

depend on interface
    A metric of 65535 is used if the specified interface is down or in status backup.

hello-interval seconds
    Set the hello interval. The default value is 10; valid range is 1-65535 seconds.

metric cost
    Set the interface metric a.k.a. cost. The default value is 10; valid range is 1-65535. A metric of 65535 is used for carp(4) interfaces with status backup.

passive
    Prevent transmission and reception of OSPF packets on this interface. The specified interface will be announced as a stub network. Passive mode is enforced for carp(4) interfaces.

retransmit-interval seconds
    Set retransmit interval. The default value is 5 seconds; valid range is 5-3600 seconds.

router-dead-time seconds
    Set the router dead time, a.k.a. neighbor inactivity timer. The default value is 40 seconds; valid range is 2-65535 seconds. When a neighbor has been inactive for router-dead-time, its state is set to DOWN. Neighbors that have been inactive for more than 24 hours are completely removed.

router-priority priority
    Set the router priority. The default value is 1; valid range is 0-255. If set to 0, the router is not eligible as a Designated Router or Backup Designated Router.

transmit-delay seconds
    Set the transmit delay. The default value is 1; valid range is 1-3600 seconds.

type p2p
    Set the interface type to point to point. This disables the election of a DR and BDR for the given interface.

FILES
/etc/ospf6d.conf
    ospf6d(8) configuration file.
/etc/examples/ospf6d.conf
    Example configuration file.

SEE ALSO
ospf6ctl(8), ospf6d(8), rc.conf.local(8)

HISTORY
The ospf6d.conf file format first appeared in OpenBSD 4.2.